Why is my well water sandy or gritty?

Well water sandy or gritty usually means sand is getting into the system from the well itself, the pump setup, or disturbed sediment in the aquifer, and the fix depends on where that sand is coming from.
Why well water turns sandy or gritty
In Central Florida, a gritty feel in well water often starts with sand entering through the well screen, casing, or pump intake. If a well is old, damaged, or drawing more aggressively than the formation can supply, it can pull fine sand into the water line.
A few common causes are:
- Worn or damaged pump components that no longer keep sediment out
- A failing well screen or casing issue that lets formation sand enter the well
- The pump set too low and pulling from a sandy zone
- A new or recently disturbed well that is still clearing sediment
- Aquifer changes around the well after drought, heavy pumping, or storm activity
If the grit is sudden, that is a sign to stop and have it checked. Continued pumping can wear out the pump faster and put sand through plumbing, valves, and fixtures.
What the grit can tell you about the well
Sand from the well itself
If the grit shows up at every faucet and in every load of laundry, the problem is often inside the well, not just in one fixture. In that case, the issue may involve screen failure, casing damage, or the pump position.
In older wells, the system may have been working for years and then finally started drawing sediment as the water level changed. That is common in a place like Polk County, where well conditions can vary from one property to the next.
Sediment after pump work or new drilling
Sometimes a well water sandy or gritty problem appears right after pump service, well work, or a new installation. That can happen while the well is clearing out loosened sediment.
A little temporary turbidity is different from ongoing sand. If the water stays gritty, you should have the well and pump inspected. We handle both Water Well Drilling and Pump Repair & Installation, so we can look at the whole system instead of treating only one part of it.
Iron and mineral buildup can add to the problem
Not every gritty water complaint is pure sand. In some wells, mineral scale or sediment buildup can make the water feel rough and leave residue in sinks, tubs, or appliances.
If your water also has odor, staining, or hardness issues, the well may need testing beyond a simple visual check. Our Water Filtration & Treatment service includes on-site water testing so we can identify what is actually in the water before recommending a fix.
What to check before you call
You do not need to take the system apart. Just note what you are seeing:
- Is the grit in every faucet or just one?
- Did it start after pump repair, a power event, or heavy rainfall?
- Does the water clear after running for a while, or does it stay sandy?
- Do you see visible sand in buckets, tubs, or filters?
- Has water pressure changed at the same time?
If your well has stopped producing water entirely, or if you are dealing with a mobile-home-park well that is down, treat it as an emergency and call right away.
How Dunham fixes sandy well water
We look at the well, the pump, the pressure system, and the water condition together. That matters because a grit problem can start in more than one place, and replacing only one part may not solve it.
Depending on what we find, the repair may involve:
- Adjusting or replacing the pump
- Inspecting the well casing and downhole setup
- Rebuilding components in our full-line machine shop
- Testing the water and adding filtration or treatment
- Checking whether the well is the right type for the property’s demand
We carry Goulds, Sta-Rite, Grundfos, and Schaefer pumps and equipment, and our on-site shop lets us rebuild many pumps and turbines in-house. That can save time when the problem is mechanical rather than a full well replacement.
If the well is primarily for irrigation, we also service Shallow (2-Inch) Irrigation Wells and irrigation systems. For properties with regular watering needs, a properly sized shallow irrigation well can be a practical way to reduce dependence on metered municipal water.
When a filter helps, and when it does not
A filter can help if the issue is minor sediment or if your water needs treatment after the main problem is corrected. But a filter is not a substitute for fixing a failing well or pump.
You may need a treatment system if you also have:
- Hard water
- Iron staining
- Hydrogen sulfide odor
- Manganese or other nuisance minerals
- Sediment that continues after the well is repaired
If the water is gritty because the well is pulling sand, filtration alone may clog quickly and mask the real issue. That is why we like to test first and diagnose the system before putting in equipment that cannot solve the root cause.
Don’t wait if the grit is getting worse
A little sand can become a bigger mechanical problem fast. Sand wears pump parts, fouls pressure tanks, and can shorten the life of appliances that use water.
If the problem started after a lightning event, we also handle Lightning Damage Repair for well systems, including pump and motor repair, pressure-switch and control replacement, and insurance claim assistance.
For abandoned wells on a property, we can also handle Well Abandonment properly and file the state rebate paperwork on your behalf when applicable.
If your well water is sandy or gritty, call Dunham Well Drilling in Winter Haven at (863) 965-2881. We’ve served Polk County and Central Florida since 1950, and with our full machine shop, pump and well expertise, and 24/7 answering service, we can help figure out what is actually causing the sand and what it will take to fix it.
Have a well or pump question?
Skip the form and call us. Our 24/7 answering service is always live.
Call (863) 965-2881