Open now: Mon–Fri · 7:30 AM – 4:30 PMLicensed Contractor · FGWA Member24/7 Answering Service(863) 965-2881

← Back to Blog

How do I know if my submersible pump is failing?

How do I know if my submersible pump is failing?

A submersible pump failing usually shows up as weak water pressure, sputtering, tripped breakers, air in the lines, or a pump that runs but doesn’t deliver steady water.

Signs of a failing submersible pump

A submersible well pump sits down in the well, so the first clues are usually changes at the taps rather than a noisy motor you can see. In Central Florida homes, common warning signs include low pressure, intermittent water, or a pump that cycles on and off more often than it should.

Watch for these symptoms:

  • Sudden loss of water pressure
  • Water that pulses or sputters
  • Breaker trips or fuse issues
  • Pump runs but water output is weak
  • Dirty or sandy water showing up with the problem
  • Pressure tank behavior changes, like rapid cycling

If the change is gradual, the pump may be wearing out. If the problem is sudden, the issue could also be electrical, a pressure switch, a pressure tank, or a lightning-related failure. We handle all of those at Dunham Well Drilling through our pump repair and installation service.

Pressure loss is not always the pump

A lot of homeowners assume the pump is bad the moment pressure drops. Sometimes it is, but not always. A clogged line, pressure tank problem, failing switch, or electrical issue can mimic pump failure.

If you have a well system and the water suddenly feels weak, do not keep resetting breakers over and over. That can create more damage. Call us so we can test the system correctly.

Common submersible pump failure symptoms in Central Florida wells

In Polk County and across Central Florida, we see a few recurring patterns. Hard water, sand, age, electrical damage, and lightning all play a role in pump wear.

1. The pump keeps losing prime or the water cuts in and out

Submersible pumps are designed to stay submerged, so when a system starts surging or losing water flow, something is off. The issue may be electrical, a damaged motor, or a problem with the well itself.

If the pump starts and stops erratically, that can also point to a pressure switch or tank issue. Our pump repair and installation work includes pressure tanks, and we rebuild pumps and turbines in-house in our full-line machine shop.

2. The breaker trips or the pump won’t start

If the breaker trips when the pump turns on, that often means the motor is drawing too much power. It can also mean lightning damage, a short, or a failed control component.

Never bypass electrical protection on a well system. That is a job for a licensed professional. If your water system has been acting up after storms, our lightning damage repair service covers pump and motor repair after a strike, plus pressure-switch and control replacement.

3. The water becomes sandy, cloudy, or dirty

A failing pump can sometimes pull sediment, especially if there is wear in the system or an issue with the well components. In some cases, the water quality issue is separate from the pump and needs treatment.

If the water smells bad, stains fixtures, or has other quality concerns along with pressure problems, it may be worth pairing pump diagnosis with our water filtration and treatment service. We offer on-site water testing to see what is actually in the water.

When the pump is failing versus when the well system is failing

A submersible pump is only one part of the system. The symptoms can overlap, so the best way to know what is wrong is to have the whole setup checked.

Likely pump problems

  • Motor failure
  • Worn pump stages
  • Electrical damage
  • A pump that is oversized or undersized for the well demand
  • Age-related wear

Likely system problems

  • Bad pressure switch
  • Failed pressure tank
  • Electrical supply problem
  • Well casing or water-level issue
  • Lightning-related damage

At Dunham, we also work on irrigation repair and installation and residential wells, so we can look at the system as a whole instead of guessing at one part in isolation.

What to do if you think your submersible pump is failing

If you notice the signs above, start by turning off anything that is clearly malfunctioning and call a well professional. Do not open electrical components or pressure equipment yourself.

Here’s the practical next step:

  1. Stop resetting the breaker repeatedly
  2. Check whether the problem is only one faucet or the whole system
  3. Notice whether the issue started after a storm
  4. Write down what you are seeing, weak pressure, no water, breaker trips, sputtering
  5. Call for service before the pump burns out completely

We serve Polk County and Central Florida from our Winter Haven shop at 1341 42nd Street NW. If your system needs a replacement, we carry Goulds, Sta-Rite, Grundfos, and Schaefer pumps, new and used, and new pump and tank installations come with the standard manufacturer’s warranty.

Why Central Florida homeowners call Dunham

Dunham Well Drilling has been family-owned since 1950, and we are a Licensed Water Well Drilling Contractor and FGWA member. We know the Polk County aquifer, and we have a full-line machine shop on-site for in-house rebuilds when a pump can be saved instead of replaced.

We also help with related well problems, from water well drilling and shallow irrigation wells to well abandonment when an old well is no longer needed. That means one call can cover more than one part of the system.

If your submersible pump failing symptoms are getting worse, call Dunham Well Drilling at (863) 965-2881 during business hours or use our 24/7 answering service. We return calls within 48 hours, and homeowners trust us because we have 76 years in business, a full machine shop, and the experience to diagnose the whole well system correctly.

Have a well or pump question?

Skip the form and call us. Our 24/7 answering service is always live.

Call (863) 965-2881
Call (863) 965-2881