How do I know if my submersible pump is failing?

A failing submersible well pump usually shows up as low water pressure, sputtering faucets, short cycling, or a pump that runs but does not deliver water consistently.
Signs a submersible well pump is failing
When a submersible pump starts wearing out, the symptoms often come on gradually. Some problems look like pump failure, but they can also point to pressure tank trouble, a bad pressure switch, wiring damage, or a well issue that needs diagnosis.
Common warning signs include:
- Low or uneven water pressure
- Water stops and starts at the faucet
- Pump runs longer than usual
- No water at all
- Breaker trips or the pump loses power
- Cloudy water or sediment after the system runs
- A clicking pressure switch or rapid cycling
If your system is acting up, don’t guess. Dunham Well Drilling handles pump repair and installation for residential, irrigation, commercial, and industrial systems, and we can test the pump, pressure tank, and controls as a system.
Low pressure is not always the pump
A weak stream at the tap does not automatically mean the pump is dying. In many cases, the issue is a pressure tank that has lost air charge, a failing pressure switch, a clogged filter, or a wiring problem.
That said, if the pressure has changed suddenly and the pump is older, the submersible pump itself may be wearing out. Our shop can diagnose the problem and, when needed, rebuild pumps and turbines in-house with our full-line machine shop.
What a failing submersible pump sounds and feels like
A healthy submersible well pump should run smoothly and shut off cleanly. When it starts failing, homeowners often notice the system acting differently even before a complete breakdown.
Common pump failure symptoms
Watch for these patterns:
- Pump runs but water flow is weak
- Pump keeps running and never reaches normal pressure
- Pump starts and stops too often
- Water pressure drops after a short use
- You hear humming, clicking, or repeated starting
- The system trips the breaker or loses power
If you have a pressure tank with your system, short cycling is a red flag. It can mean the pump is working too hard, but it can also mean the tank or switch is failing. We check the whole setup so the wrong part does not get replaced first.
Electrical issues can mimic pump failure
Submersible pumps rely on electrical service, control components, and wiring. A damaged wire, burned contact, bad pressure switch, or lightning-related issue can make a pump seem dead when the motor itself is still usable.
In Polk County, lightning damage is a real concern. Dunham provides lightning damage repair for well systems, including pump and motor repair, pressure-switch and control replacement, and insurance claim assistance.
What causes a submersible pump to fail
Submersible pumps do not usually fail all at once without a reason. Wear, water conditions, electrical problems, and age all play a part.
The most common causes
- Normal wear over time
- Sand or sediment in the well
- Electrical damage from lightning or power problems
- A failing pressure tank that overworks the pump
- Corrosion or mineral buildup
- Incorrect pump sizing for the water demand
- Dry-running or low-water conditions
In Central Florida, water conditions and aquifer geology matter. Dunham has three generations of drilling experience in the Polk County aquifer, so we understand how local well conditions affect pump performance and replacement choices.
A pump that is undersized for irrigation demand may run too often. A pump that is oversized can create pressure problems and unnecessary stress on the system. Proper diagnosis matters more than replacing parts at random.
When to call for submersible well pump repair
If your well system is giving you any of the signs below, it is time to call for service:
- No water from the well
- Repeated loss of pressure
- Frequent breaker trips
- Pump starts but does not build pressure
- Rust, sand, or sediment appears in the water
- The system is cycling on and off too often
Do not try to troubleshoot electrical components, pressure tanks, or deeper well equipment yourself. Call a licensed well contractor instead. Dunham is a Licensed Water Well Drilling Contractor and a member of the Florida Ground Water Association (FGWA), and we work on well systems across Polk County and Central Florida.
Repair or replace? What we look at
A submersible pump does not always need to be replaced. Sometimes a repair is enough, especially if the issue is a switch, control, motor component, or wiring problem.
We look at:
- Pump age and condition
- Motor performance
- Pressure tank condition
- Electrical components
- Well depth and water demand
- Signs of sediment, corrosion, or lightning damage
If replacement is the better call, we carry Goulds, Sta-Rite, Grundfos, and Schaefer pumps and pressure equipment. New pump and tank installations include the standard manufacturer’s warranty on those components.
For customers with irrigation systems, we also provide irrigation repair and installation, including pump diagnosis and repair plus hard-to-locate parts from our warehouse.
Why Central Florida well owners call Dunham
Submersible pump issues are not just a plumbing problem. They are a well-system problem, and the right fix depends on the pump, the tank, the controls, and the local water conditions.
Dunham Well Drilling has been serving Winter Haven and Polk County since 1950. Our shop at 1341 42nd Street NW, Winter Haven, FL 33881 handles pump work, well drilling, irrigation, filtration, and well abandonment, and our team can test what is actually wrong instead of guessing.
If your water pressure has changed, your pump is short cycling, or your well has stopped producing water, call (863) 965-2881 and ask for our 24/7 answering service. We return calls within 48 hours, and with 76 years in business plus an on-site machine shop, Dunham is set up to diagnose, repair, and replace submersible well pump systems the right way.
Have a well or pump question?
Skip the form and call us. Our 24/7 answering service is always live.
Call (863) 965-2881