Why does my well pump click but not start?

A well pump clicks but won’t start when the control or pressure switch is trying to call for water, but the pump, motor, capacitor, wiring, or pressure system is keeping it from running.
Why a well pump clicks but won’t start
When a well pump clicks, you’re usually hearing the pressure switch or a control relay close. That click means the system is asking the pump to turn on, but something in the pump circuit is stopping it from starting.
In Central Florida homes, the most common causes are a failed pressure switch, a bad start capacitor, low voltage, a damaged motor, or a pressure problem that keeps the system from cycling properly. If the pump is clicking repeatedly but never actually starting, don’t keep resetting it over and over. That can make the electrical damage worse.
Common reasons the pump clicks
Bad pressure switch contacts
The switch may click, but the contacts may be burnt or not passing power.Failed capacitor
Many pumps need a capacitor to get started. If it fails, you may hear a click, then nothing.Loose or damaged wiring
A connection at the switch, control box, motor, or pressure tank area can interrupt the start signal.Low voltage
If the motor isn’t getting enough power, it may hum, click, or stay silent instead of starting.Seized pump or motor
Sand, age, corrosion, or internal wear can prevent the motor from spinning.Pressure tank or system issue
A faulty tank or switch setup can cause rapid clicking or short cycling.
If your system is older, the problem may not be one single part. We often find a worn switch plus a tired pump or motor on the same job.
What you can safely check before calling
If you’re comfortable doing so, you can take a quick look at the system without opening electrical components. Keep clear of exposed wiring and never touch live parts.
- Check whether the breaker has tripped.
- Look at the pressure gauge, if your system has one.
- Listen for a hum, click, or repeated relay noise.
- Note whether the issue started after lightning, a storm, or a power outage.
- See whether the problem affects every faucet or only one zone.
If you smell burning, see sparking, or the breaker trips again right away, stop there and call for service. Electrical problems at the pump should be handled by a professional.
Pressure switch, capacitor, or motor problem?
A lot of homeowners assume the pump itself is bad as soon as it clicks and won’t start. Sometimes that’s true, but the pressure switch is often the first place to look. The switch is what tells the pump when to run, and worn contacts can click without actually sending power through.
A capacitor issue usually shows up as a click with no start, or a brief attempt to start and then failure. A motor that has burned windings or internal damage may also click or hum without turning. If the motor is locked up, it needs proper diagnosis before anything else is replaced.
Signs the issue may be electrical
- The pump clicks but never starts
- The breaker trips when the system tries to run
- You hear humming before it shuts off
- The problem started after lightning or a storm
- The pump starts only sometimes
In Florida, lightning damage is a real possibility. At Dunham Well Drilling, we handle lightning damage repair for well systems, including pump and motor repair after a strike, so that’s one thing worth checking if the failure followed a storm.
Why Central Florida wells see this problem
Well systems in Polk County and the surrounding area work hard. Between sandy soils, irrigation demand, aging equipment, and storm-related electrical damage, a pump can develop start problems over time.
For homeowners in Winter Haven and across Central Florida, the issue may also be tied to the water system itself. If your well has sand intrusion, pressure fluctuations, or a failing tank, the pump may be under more stress than it should be. That’s one reason it helps to have a shop that can diagnose both the pump and the pressure side.
We serve the area from our Winter Haven shop at 1341 42nd Street NW, and we’ve been working on wells in Polk County since 1950. That experience matters when a system is clicking but not starting and the cause isn’t obvious.
When to call for pump repair
Call a well professional if:
- The pump clicks but won’t start more than once
- The breaker keeps tripping
- The pump hums, then stops
- Water pressure has dropped or disappeared
- The problem started after lightning or a power event
- You suspect the pressure switch, capacitor, motor, or wiring
If you need help with a pump that clicks but won’t start, our Pump Repair & Installation service covers residential pumps, irrigation pumps, turbine pumps, industrial pumps, centrifugal pumps, and pressure tanks. We also have a full-line machine shop for in-house rebuilds, and we carry Goulds, Sta-Rite, Grundfos, and Schaefer pumps.
If the failure is part of a broader water issue, our Water Filtration & Treatment and Lightning Damage Repair services may also be part of the solution.
Call Dunham Well Drilling at (863) 965-2881 when your well pump clicks but won’t start, especially after a storm or power problem. With 76 years in business, a family-run shop in Winter Haven, and in-house pump rebuild capability, we can help diagnose the problem and get you pointed to the right repair.
Have a well or pump question?
Skip the form and call us. Our 24/7 answering service is always live.
Call (863) 965-2881