Why is my well pump running but no water?

A well pump running but no water usually means the pump is losing prime, the water level has dropped below the intake, the pressure switch or control has failed, or there is a leak, clog, or electrical problem somewhere in the system.
Well pump running but no water: the most common causes
When a pump sounds like it is working but the faucets stay dry, the problem is usually not one single thing. In Central Florida, we see this on both shallow irrigation wells and deeper drinking-water wells, and the fix depends on whether the issue is at the pump, the well, or the pressure system.
Common causes include:
- Loss of prime in a jet pump system
- Low water level in the well
- Clogged intake, screen, or piping
- Bad foot valve or check valve
- Pressure switch failure
- Electrical problems at the pump or control box
- A leak in the drop pipe, suction line, or pressure side
- Pump wear or failure
If the pump is still running but no water is moving, keep an eye on the system. A pump that runs dry can overheat and cause more damage, which turns a repair into a bigger one.
What to check before you call for service
There are a few simple things a homeowner can notice safely, but anything involving electrical service, pressure tanks, or well components deeper than a hand-driven shallow point should be handled by a professional.
Signs the problem is on the pump side
If you hear the pump running and see no pressure build, the issue may be with the pump itself or the parts that help it move water. That can include a worn impeller, air in the line, a failed check valve, or a bad pressure switch.
If the pump has been cycling on and off strangely, or it runs continuously without building pressure, that points to a deeper system issue. In those cases, we usually need to test the pump, inspect the system, and determine whether repair or replacement makes more sense.
Signs the problem is in the well
Sometimes the pump is fine, but the well is not supplying water. That can happen if the water table drops below the intake, especially in a shallow well used for irrigation. It can also happen if the well has a blockage, scale buildup, or casing problem.
For properties using Shallow (2-Inch) Irrigation Wells, seasonal changes in the water table matter. If the well no longer reaches dependable water, the pump may run without producing flow even though nothing sounds obviously broken.
Why this happens in Central Florida wells
Polk County and the surrounding area have their own well conditions, and that matters when a pump is running but no water is coming through. Some wells are shallow irrigation wells, while others are deeper wells for drinking water or higher-volume use. The cause is often tied to the type of well, how it was built, and what the aquifer is doing now.
At Dunham Well Drilling, we’ve worked with Polk County aquifer geology for three generations. That experience helps when we are diagnosing whether the issue is a pump problem, a well problem, or a pressure-system problem.
For new systems, our Water Well Drilling service covers residential, agricultural, and commercial wells, including site evaluation and casing selection. That matters because a well that was built for the wrong demand can struggle later when the home, irrigation load, or water use changes.
Pump repair, pressure tanks, and filtration issues
Sometimes the pump is only part of the story. A bad pressure tank, a failing switch, or a water quality issue can make it seem like the well has quit when the real problem is elsewhere.
Pressure systems and pump repair
If the pressure tank has failed, or if the pressure switch is not reading correctly, the pump may run without producing usable water at the tap. Those parts need proper diagnosis, and they should not be guessed at.
We handle Pump Repair & Installation for residential pumps, irrigation pumps, turbine pumps, industrial pumps, centrifugal pumps, and pressure tanks. We also carry Goulds, Sta-Rite, Grundfos, and Schaefer pumps and can rebuild many units in our full-line machine shop.
Water quality problems that reduce flow
Heavy iron buildup, sediment, or other water quality issues can restrict flow and cause trouble in the system. If you are also seeing staining, odor, or hard water, the fix may involve more than pump work.
Our Water Filtration & Treatment service includes softeners, chlorination systems, iron removal, iron-sequestering systems, and hydrogen sulfide treatment. We also do on-site water testing to help identify what is actually in the water, which is useful when the symptom is low or no flow.
When to call for professional help
Call right away if:
- The pump runs continuously and no water comes out
- The pump is cycling rapidly
- You smell burning or hear unusual noises
- Water flow stopped suddenly
- The problem started after lightning, a storm, or a power issue
- You have a drinking water well or a mobile-home-park well that is down
If lightning struck nearby, the issue may involve the motor, pressure switch, control box, or wiring. We also handle Lightning Damage Repair and work directly with your insurance company on the claim when applicable.
If an old well is no longer needed, Well Abandonment is another service we provide, including state rebate paperwork filed on the customer’s behalf.
Call Dunham for well pump troubleshooting in Central Florida
If your well pump is running but no water is coming out, call Dunham Well Drilling at (863) 965-2881 as soon as you notice the problem. We offer a 24/7 answering service, and calls are returned within 48 hours. With 76 years in business, a full machine shop for in-house pump rebuilds, and service across Polk County and Central Florida, we can help diagnose the issue and get you pointed to the right fix.
Have a well or pump question?
Skip the form and call us. Our 24/7 answering service is always live.
Call (863) 965-2881