Open now: Mon–Fri · 7:30 AM – 4:30 PMLicensed Contractor · FGWA Member24/7 Answering Service(863) 965-2881

← Back to Blog

What causes a shallow well pump to lose prime?

What causes a shallow well pump to lose prime?

A shallow well pump losing prime usually means air is getting into the suction side, water is leaking back out of the pump, or the pump has a worn part that can’t hold a prime between cycles.

What “lose prime” means on a shallow well pump

A shallow well pump depends on a water-filled suction line to pull water from the well. If that line fills with air, the pump can spin without moving water. You may hear the motor run, but the pressure will drop and the system will stop delivering water.

In Central Florida, we see this most often on irrigation systems and shallow wells serving homes or mobile-home lots. If you need help with a failing shallow system, our Shallow (2-Inch) Irrigation Wells page explains the type of system we install and service, and our Pump Repair & Installation service covers the pump side of the problem.

Common reasons a shallow well pump loses prime

A shallow well pump usually loses prime for one of a few practical reasons. Some are simple wear items, and some point to a deeper issue in the well or piping.

1. Air leak on the suction side

The most common cause is an air leak anywhere between the well and the pump. Even a small leak can break the vacuum the pump needs to lift water.

Typical trouble spots include:

  • Loose fittings
  • Cracked suction pipe
  • Deteriorated sealant on threaded joints
  • Worn pump lid gasket or seal
  • Faulty foot valve or check valve

Air leaks can be hard to see because they do not always leak water. They can let air in when the pump shuts off, then the pump starts dry the next time it runs.

2. Bad foot valve or check valve

A foot valve or check valve is supposed to hold water in the line after the pump shuts off. If that valve is stuck open, worn, or clogged with debris, water drains back into the well and the pump loses prime.

This is especially common on older systems or wells with sediment problems. If the well water carries sand, scale, or iron buildup, the valve may not seal properly.

3. Low water level in the well

If the water level drops too far, the pump may start pulling air instead of water. That can happen during dry periods, after heavy irrigation demand, or if the pump is set up for a water level it can no longer reach.

A shallow well setup depends on local conditions. In Polk County, the aquifer and seasonal water levels vary from area to area, which is one reason proper site evaluation matters before drilling or setting a pump. Our Water Well Drilling service includes site evaluation and casing selection for new wells.

4. Worn pump components

If the pump itself is worn, it may not be able to create enough suction to stay primed. Common wear points include the impeller, diffuser, seals, and gaskets.

When a pump is older, rusted, or repeatedly run dry, repairs may be more practical than trying to nurse it along. Dunham’s Pump Repair & Installation service includes in-house rebuilds in our full-line machine shop, which is useful when a pump needs more than a quick part swap.

5. Clogged suction line or strainer

Debris, scale, or sediment can restrict the flow into the pump. The pump may sound like it is working, but it cannot keep a solid water column moving through the line.

This can show up as:

  • Weak pressure
  • Pump short-cycling
  • Air in the water
  • Repeated loss of prime after shutoff

If the pump is fighting sediment, the well itself may need service, not just the pump.

Signs the problem is not just the pump

A shallow well pump can lose prime because of the pump, but the real issue is not always inside the pump housing. Watch for these warning signs:

  • The pump runs but no water comes out
  • Water pressure drops suddenly after normal operation
  • The pump needs to be manually re-primed often
  • You hear gurgling or sputtering at the fixtures
  • The system works for a short time, then fails again

If you also notice dirty water, rust staining, rotten-egg odor, or hard water scale, the problem may involve water quality as well. Our Water Filtration & Treatment service addresses hard, smelly, or staining well water, and we can test the water on site to see what is actually in it.

How we diagnose shallow well prime problems

At Dunham Well Drilling, we look at the whole system, not just the pump. That matters because a prime issue can come from the well, the piping, the pump, or the controls.

We typically check:

  • Suction-side fittings and pipe condition
  • Check valve or foot valve operation
  • Pump seal, gasket, and housing condition
  • Water level and well suitability
  • Pressure tank and pressure switch function
  • Signs of sediment, iron, or scale buildup

Because we handle both pump work and well work, we can follow the problem to its source instead of guessing. That is one reason customers in Winter Haven and across Polk County call us for Winter Haven well service and other local service-area work.

When to call for help

If your shallow well pump keeps losing prime, stop resetting it over and over. Running a pump dry can damage the motor and shorten the life of the system. Electrical service, pressure tanks, and well equipment should be handled by a professional.

Call us if:

  • You have to reprime the pump repeatedly
  • Water pressure keeps dropping
  • The pump runs but will not deliver water
  • You suspect a leak, valve problem, or worn pump parts
  • The well is shallow and the system is older or inconsistent

We’re a family-owned company founded in 1950, a [FGWA member] and a [Licensed Water Well Drilling Contractor], and we work with the kind of shallow well systems common across Central Florida.

If your shallow well pump losing prime is interrupting water at home or on irrigation, call Dunham Well Drilling at (863) 965-2881. With 76 years in business and an on-site machine shop for pump rebuilds, we can find the real cause and get the system back on track.

Have a well or pump question?

Skip the form and call us. Our 24/7 answering service is always live.

Call (863) 965-2881
Call (863) 965-2881