Open now: Mon–Fri · 7:30 AM – 4:30 PMLicensed Contractor · FGWA Member24/7 Answering Service(863) 965-2881

← Back to Blog

What causes a shallow well pump to trip the breaker?

What causes a shallow well pump to trip the breaker?

A shallow well pump that keeps tripping the breaker is usually dealing with an electrical fault, a failing motor, low voltage, or a pump problem that makes the motor work too hard.

What causes a shallow well pump to keep tripping the breaker?

When a shallow well pump trips a breaker, the breaker is doing its job: it is shutting the circuit off because something is drawing too much current or shorting out. On a shallow well system, that can come from the pump motor itself, a wiring problem, a bad pressure switch, or a pressure tank issue that causes the pump to cycle too often.

If your system keeps resetting and tripping again, do not keep forcing it back on. That can burn up the motor, damage controls, or turn a small repair into a full pump replacement. Call a professional who handles both pump repair and well system diagnostics, like our team at Dunham Well Drilling in Winter Haven.

Common reasons a shallow well pump trips the breaker

1. A failing or seized pump motor

A motor that is wearing out may pull extra amperage every time it starts. If the bearings are bad, the motor is overheating, or the internal windings are failing, the breaker may trip right away or after a short run time.

This is one of the most common reasons we see for a pump that will not stay running. With our on-site machine shop, we can rebuild many pumps and turbines in-house as part of our Pump Repair & Installation service.

2. Low voltage or loose electrical connections

If the pump is not getting proper voltage, the motor works harder to start and run. That extra strain can trip the breaker, especially during startup. Loose wiring, corroded connections, or a worn pressure switch can all contribute to the problem.

Electrical issues around a well system should be handled by a qualified contractor. Do not try to troubleshoot live wiring yourself.

3. A bad pressure switch

The pressure switch tells the pump when to turn on and off. If the contacts are burned, the switch is stuck, or the wiring at the switch is damaged, the pump may short cycle or draw too much power. Either condition can cause the breaker to trip.

A pressure switch problem can look like a pump failure, but it may be a control issue instead. That is why we test the whole system, not just the pump.

4. A pressure tank problem

A waterlogged or failing pressure tank can make the pump cycle constantly. That repeated starting and stopping is hard on the motor and can cause the breaker to trip. In some cases the tank bladder has failed, or the tank has lost its air charge.

If your pump is kicking on every few seconds, the tank should be checked right away. We service pressure tanks as part of our pump work.

5. A clogged intake or pump restriction

If the pump is trying to move water through a restricted line, clogged screen, or damaged piping, it may overwork and trip the breaker. In shallow well systems, a drop in water level can also make the pump lose prime or run inefficiently.

A shallow well in Central Florida can perform well for irrigation, but only if the well, piping, and pump are matched correctly. Our Shallow (2-Inch) Irrigation Wells page explains where these systems are often a good fit.

6. Lightning or surge damage

In Polk County and across Central Florida, lightning can damage pump motors, switches, and control components. A surge may not stop the system immediately, but it can weaken a part until it starts tripping the breaker later.

We provide Lightning Damage Repair for well systems, including pump and motor repair, pressure-switch replacement, and insurance claim assistance.

What you should check first

Before calling for service, you can safely look at a few basic things:

  • Reset behavior: Does the breaker trip instantly, or only after the pump runs for a few seconds?
  • Pump noise: Is the motor humming, struggling, or making unusual sounds?
  • Pressure gauge: Is the system building pressure normally?
  • Frequent cycling: Is the pump turning on and off too often?
  • Other electrical problems: Are lights dimming or other circuits acting up?

If the breaker trips immediately every time, stop resetting it. That usually points to a short, motor fault, or wiring issue that needs professional diagnosis.

Why this happens often with shallow well systems in Central Florida

Shallow wells are common for irrigation in Polk County because they can be a cost-effective alternative to metered municipal water. But shallow well systems depend on proper pump sizing, correct pressure settings, and the right water level for the property.

In our area, a shallow well can work very well for regular irrigation demand. It can also become troublesome if the pump is undersized, the water table changes, or the electrical components are aging. We know which Polk County areas support reliable shallow wells because we have worked this ground for three generations.

If your system is beyond a simple repair, we can also help with new Water Well Drilling for residential, agricultural, and commercial properties across Central Florida.

When to call a well professional

Call for service if:

  • The breaker trips repeatedly
  • The pump will not restart
  • You smell burning electrical components
  • The pressure tank is short cycling the pump
  • The system hums but will not build pressure
  • You suspect lightning damage or a motor failure

We handle both pump and filter work, which helps when the issue is part electrical, part water quality, or part system design. That one-call approach is often faster than piecing together multiple contractors.

If you need help diagnosing what causes a shallow well pump to keep tripping, call Dunham Well Drilling at (863) 965-2881. We have been serving Winter Haven and Polk County since 1950, we offer a 24/7 answering service, and our full machine shop lets us rebuild many pumps and turbines in-house.

Have a well or pump question?

Skip the form and call us. Our 24/7 answering service is always live.

Call (863) 965-2881
Call (863) 965-2881