What causes a well pressure tank to lose air?

A well pressure tank loses air for a few common reasons: a hidden water leak, a bad air-control component, a leaking bladder, or a pressure switch and piping problem that keeps the system from cycling correctly.
Why a well pressure tank loses air
In a properly working system, the air charge and water volume inside the tank work together to keep pressure steady. If the tank keeps losing air, the system starts short-cycling, the pressure may swing too fast, and the pump can wear out sooner.
The most common causes are:
- A damaged bladder or diaphragm in a bladder tank
- A leaking Schrader valve on the air stem
- A plumbing leak in the tank tee, fittings, or nearby piping
- A bad pressure switch or control issue causing abnormal cycling
- A waterlogged tank where the air cushion is no longer doing its job
- Corrosion or damage inside the tank, especially in older systems
If your tank is repeatedly losing air, it usually means there is a mechanical problem somewhere in the system, not just a need for occasional top-off air.
Signs your pressure tank is the problem
A tank that is losing air often shows up in the way the water system behaves. You may notice one or more of these:
- The pump turns on and off more often than usual
- Water pressure feels weak, then surges
- The pressure gauge bounces a lot
- The tank sounds empty or “hollow”
- You keep adding air, but the system loses it again
- The pump runs longer than it used to
If the tank is on a well system, don’t ignore these symptoms. Repeated air loss can point to a failing tank, a leak, or a pressure problem that needs professional service. For pump repair and installation, we handle pressure tanks, residential pumps, and full system troubleshooting at Dunham Well Drilling: /pumps/
Bladder failure: the most common reason
Many modern pressure tanks use a bladder or diaphragm to separate the air and water. When that internal bladder fails, water can enter the air side of the tank and the air charge disappears.
What bladder failure looks like
A failing bladder often causes:
- Rapid short cycling
- Water coming out of the air valve
- A tank that feels full of water
- Pressure swings that get worse over time
Once the bladder fails, the tank usually needs replacement rather than a quick repair. That is especially true if the tank is older or if the tank shell has started to corrode.
Leaks in the tank valve, fittings, or piping
Sometimes the tank itself is not the issue. Air can escape through a leaking valve stem, loose fitting, cracked pipe, or a bad threaded connection near the tank.
This is why a pressure tank problem should not be diagnosed by guesswork alone. A system that loses air may actually have a slow leak on the water side that is creating the pressure symptoms you notice at the tank.
Common leak points include:
- The air valve core
- Tank tee fittings
- Pressure gauge threads
- Pressure switch piping
- Check valve connections
- Nearby shutoff valves
If the leak is on the plumbing side, the fix may be different from a tank replacement. Our team can evaluate the whole setup, and because we also do pump work in-house, we can address the system as a unit instead of treating each part separately.
When the pressure switch is part of the problem
A pressure switch does not hold air, but it can contribute to symptoms that look like air loss. If the switch is failing or the settings are wrong, the pump may cycle too often and make the system seem unstable.
That can happen when:
- The switch is clogged
- The contacts are worn
- The pressure range is set incorrectly
- The switch is damaged after lightning or electrical trouble
If your well system has electrical issues, do not try to work on the wiring yourself. That belongs with a qualified well contractor. Dunham also provides lightning damage repair for well systems when the pump, motor, controls, or pressure switch have been affected.
Why Central Florida wells can show these problems
In Polk County and across Central Florida, well systems work hard year-round. Irrigation demand, mineral content, and age all play a role in wear on tanks, pumps, and controls.
We see pressure tank problems tied to:
- Long irrigation run times
- Old tanks that have reached the end of service life
- Mineral buildup in fittings and switches
- Lightning-related electrical damage
- Pumps that are oversized or cycling too often
For properties that use wells for irrigation, the system may be under even more stress. If you need help with irrigation-related well issues, our irrigation repair and installation service covers pumps, controllers, valves, pipes, and hard-to-find parts.
How we diagnose a tank that keeps losing air
At Dunham Well Drilling, we look at the whole system, not just the tank. That includes the pressure switch, plumbing connections, tank condition, pump behavior, and the rest of the well setup.
Our process may include:
- Checking the tank air charge
- Testing the pressure switch operation
- Inspecting fittings and valve stems for leaks
- Looking for signs of a failed bladder
- Evaluating pump cycling and system pressure
- Checking for related water quality issues if needed
We also have a full-line machine shop on site, so pumps and turbines can be rebuilt in-house when that is the right fix.
Repair or replace?
Whether to repair or replace depends on what is actually failing. A valve leak or loose fitting may be repairable. A ruptured bladder or corroded tank usually means replacement.
Replacement is often the better choice when:
- The tank is old
- The bladder has failed
- The tank is waterlogged
- Corrosion is visible
- The system keeps short-cycling after minor repairs
If you are unsure, it is better to have the system checked before the pump gets damaged from repeated cycling.
If your well pressure tank loses air, call Dunham Well Drilling at (863) 965-2881 during business hours or use our 24/7 answering service after hours. We’ve been serving Polk County since 1950, and we can troubleshoot the tank, pump, switch, or plumbing side of the system with the kind of experience that comes from three generations in the Central Florida well trade.
Have a well or pump question?
Skip the form and call us. Our 24/7 answering service is always live.
Call (863) 965-2881